Enterasys Enterasys SecureStack B2 B2G124-24 Specifiche Pagina 308
- Pagina / 488
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
VLAN Configuration Command Set
Assigning Port VLAN IDs (PVIDs) and Ingress Filtering
6-12 SecureStack B2 Configuration Guide
6.3.3 Assigning Port VLAN IDs (PVIDs) and Ingress Filtering
Purpose
To assign default VLAN IDs to untagged frames on one or more ports, to configure VLAN ingress
filtering and constraints, and to set the frame discard mode.
Commands
The commands used to configure port VLAN IDs and ingress filtering are listed below and
described in the associated section as shown.
• show port vlan (Section 6.3.3.1)
• set port vlan (Section 6.3.3.2)
• clear port vlan (Section 6.3.3.3)
• show port ingress filter (Section 6.3.3.4)
• set port ingress filter (Section 6.3.3.5)
• show port discard (Section 6.3.3.6)
• set port discard (Section 6.3.3.7)
• clear port discard (Section 6.3.3.8)
- SecureStack B2 1
- 1.01.xx 3
- Enterasys Networks, Inc 4
- Firmware License Agreement 4
- PORT CONFIGURATION 10
- SNMP CONFIGURATION 11
- SPANNING TREE CONFIGURATION 12
- 802.1Q VLAN CONFIGURATION 13
- Contents 14
- IGMP CONFIGURATION 15
- SECURITY CONFIGURATION 17
- About This Guide 23
- STRUCTURE OF THIS GUIDE 24
- RELATED DOCUMENTS 25
- Related Documents 26
- Introduction 27
- 1.2 DEVICE MANAGEMENT METHODS 28
- 1.3 GETTING HELP 29
- Getting Help 30
- Factory Default Settings 32
- 2.1.3 CLI Command Modes 35
- 2.1.4 Using WebView 36
- Displaying WebView status: 36
- Enabling / disabling WebView: 36
- • ro for Read-Only access 37
- • rw for Read-Write access 37
- User Account 38
- --More-- to indicate 40
- Key Sequence Command 41
- Important 44
- 2.1.10.2 show switch 47
- 2.1.10.5 set switch 51
- 2.1.10.6 set switch copy-sw 52
- 2.1.10.9 set switch member 55
- 2.1.10.10 clear switch member 56
- 2.1.10.13 save config 59
- 2.1.11.1 show system login 61
- 2.1.11.2 set system login 63
- 2.1.11.3 clear system login 64
- 2.1.11.4 set password 65
- 2.1.11.8 show system lockout 69
- 2.1.11.9 set system lockout 70
- 2.1.12.1 show ip address 73
- 2.1.12.2 show ip protocol 74
- 2.1.12.3 set ip address 75
- 2.1.12.4 show system 76
- 2.1.12.5 show system hardware 78
- 2.1.12.7 show time 80
- 2.1.12.8 set time 81
- 2.1.12.9 show summertime 82
- 2.1.12.10 set summertime 83
- 2.1.12.11 set summertime date 84
- 02:00 60 85
- 2.1.12.13 clear summertime 86
- 2.1.12.14 set prompt 87
- 2.1.12.15 show version 88
- 2.1.12.16 set system name 89
- 2.1.12.17 set system location 90
- 2.1.12.18 set system contact 91
- 2.1.12.19 set length 92
- 2.1.12.20 show logout 93
- 2.1.12.21 set logout 94
- 2.1.12.22 show console 95
- 2.1.12.23 set console baud 96
- 2.1.13.1 show inlinepower 98
- 2.1.13.3 set inlinepower trap 100
- 2.1.13.5 set port inlinepower 102
- • Tera Term Pro Version 2.3 103
- 2.1.14.3 show boot system 107
- 2.1.14.4 set boot system 108
- Commands 109
- 2.1.15.1 show telnet 110
- 2.1.15.2 set telnet 111
- 2.1.16.1 dir 113
- 2.1.16.2 show config 114
- 2.1.16.3 configure 116
- 2.1.16.4 copy 117
- 2.1.16.5 delete 118
- 2.1.17 Configuring CDP 119
- 2.1.17.1 show cdp 120
- Output What It Displays 121
- 2.1.17.2 set cdp state 122
- 2.1.17.3 set cdp auth 123
- 2.1.17.4 set cdp interval 124
- 2.1.17.5 set cdp hold-time 125
- 2.1.17.6 clear cdp 126
- 2.1.18.1 cls (clear screen) 128
- 2.1.18.2 exit 129
- 2.1.19 Resetting the Device 129
- 2.1.19.1 reset 130
- 2.1.19.2 clear config 131
- Resetting the Device 132
- Port Configuration 133
- Examples 134
- 3.3.1 Reviewing Port Status 136
- 3.3.1.1 show port 137
- 3.3.1.2 show port status 138
- 3.3.1.3 show port counters 140
- 3.3.2.1 set port disable 144
- 3.3.2.2 set port enable 145
- 3.3.2.3 show port trap 146
- 3.3.3.1 show port speed 148
- 3.3.3.2 set port speed 149
- 3.3.3.3 show port duplex 150
- 3.3.3.4 set port duplex 151
- 3.3.4.1 show port jumbo 153
- 3.3.4.2 set port jumbo 154
- 3.3.4.3 clear port jumbo 155
- 3.3.5.1 show port negotiation 156
- 3.3.5.2 set port negotiation 157
- 3.3.6 Setting Flow Control 158
- 3.3.6.1 show flowcontrol 159
- 3.3.6.3 set flowcontrol 160
- 3.4 PORT MIRRORING 161
- 3.4.1 Mirroring Features 161
- 3.4.2 Setting Port Mirroring 161
- 3.4.2.1 show port mirroring 162
- 3.4.2.2 set port mirroring 163
- 3.4.2.3 clear port mirroring 164
- 3.5.1 LACP Operation 165
- 3.5.2 LACP Terminology 166
- Configuring Link Aggregation 168
- 3.5.4.1 set lacp 170
- 3.5.4.2 show lacp 171
- 3.5.4.3 set lacp asyspri 173
- 3.5.4.4 set lacp aadminkey 174
- 3.5.4.5 clear lacp 175
- 3.5.4.6 set lacp static 176
- 3.5.4.7 clear lacp static 177
- 3.5.4.8 show port lacp 178
- 3.5.4.9 set port lacp 180
- (Section 3.5.4.3) 181
- 3.5.4.10 clear port lacp 183
- 3.5.5.1 show broadcast 186
- 3.5.5.2 set broadcast 187
- SNMP Configuration 189
- 4.1.2 SNMPv3 190
- SNMP Configuration Summary 191
- 4.3.1.1 show snmp engineid 195
- 4.3.1.2 show snmp counters 196
- 4.3.2.1 show snmp user 203
- 4.3.2.2 set snmp user 205
- 4.3.2.3 clear snmp user 206
- 4.3.2.4 show snmp group 207
- 4.3.2.5 set snmp group 209
- 4.3.2.6 clear snmp group 210
- 4.3.2.7 show snmp community 211
- 4.3.2.8 set snmp community 212
- 4.3.2.9 clear snmp community 213
- 4.3.3.1 show snmp access 215
- 4.3.3.2 set snmp access 218
- 4.3.3.3 clear snmp access 220
- 4.3.4.1 show snmp view 222
- 4.3.4.2 show snmp context 224
- 4.3.4.3 set snmp view 225
- 4.3.4.4 clear snmp view 226
- 4.3.5.2 set snmp targetparams 231
- 4.3.6.1 show snmp targetaddr 235
- 4.3.6.2 set snmp targetaddr 237
- TrapSink 238
- 4.3.6.3 clear snmp targetaddr 239
- 4.3.7.1 show snmp notify 241
- 4.3.7.2 set snmp notify 243
- 4.3.7.3 clear snmp notify 244
- About SNMP Notify Filters 244
- 4.3.7.5 set snmp notifyfilter 246
- and associate a target 249
- Spanning Tree Configuration 255
- 5.1.2 Spanning Tree Features 256
- 5.2.1.1 show spantree stats 259
- 5.2.1.2 set spantree 262
- 5.2.1.3 show spantree version 263
- 5.2.1.4 set spantree version 264
- 5.2.1.7 set spantree msti 267
- 5.2.1.8 clear spantree msti 268
- 5.2.1.9 show spantree mstmap 269
- 5.2.1.10 set spantree mstmap 270
- 5.2.1.18 set spantree hello 278
- 5.2.1.19 clear spantree hello 279
- 5.2.1.20 set spantree maxage 280
- 5.2.2.3 show spantree portpri 287
- 5.2.2.4 set spantree portpri 288
- 802.1Q VLAN Configuration 297
- 6.1.1 Port Assignment Scheme 298
- • show vlan (Section 6.3.1.1) 300
- 6.3.1.1 show vlan 301
- 6.3.2.1 set vlan 304
- 6.3.2.2 set vlan name 305
- 6.3.2.3 clear vlan 306
- 6.3.2.4 clear vlan name 307
- 6.3.3.1 show port vlan 309
- 6.3.3.2 set port vlan 310
- 6.3.3.3 clear port vlan 311
- 6.3.3.6 show port discard 314
- 6.3.3.7 set port discard 315
- 6.3.3.8 clear port discard 316
- 6.3.4.1 show port egress 318
- 6.3.4.2 set vlan forbidden 319
- 6.3.4.3 set vlan egress 320
- 6.3.4.4 clear vlan egress 322
- 6.3.5 Setting the Host VLAN 323
- 6.3.5.1 show host vlan 324
- 6.3.5.2 set host vlan 325
- 6.3.5.3 clear host vlan 326
- Purpose 328
- 1H152-51 329
- 6.3.7.1 show gvrp 331
- 6.3.7.2 show garp timer 332
- 6.3.7.3 set gvrp 334
- 6.3.7.4 clear gvrp 335
- 6.3.7.5 set garp timer 336
- CONFIGURATION 337
- {enable 339
- 7.3.2.1 show diffserv info 341
- 7.3.2.2 show diffserv class 342
- 7.3.2.3 set class create 343
- Section 7.3.3.5) 350
- Section 7.3.3.6) 350
- Section 7.3.3.7) 350
- 7.3.3.1 show diffserv policy 351
- Section 7.3.4.3 353
- associate to this policy 355
- 7.3.4.3 set diffserv service 361
- Configuration 363
- COMMAND SET 364
- 8.3.1.1 show port priority 365
- 8.3.1.2 set port priority 366
- 8.3.1.3 clear port priority 367
- • 100Base-T - 4 370
- • 1000Base-T - 4 370
- • 1000Base-X - 8 370
- 8.3.3.1 show port ratelimit 373
- 8.3.3.2 set port ratelimit 375
- This example shows how to: 376
- 8.3.3.3 clear port ratelimit 377
- IGMP Configuration 379
- IGMP Configuration Summary 380
- Enabling / Disabling IGMP 380
- 9.4.1.1 show igmpsnooping 381
- 9.4.2 Configuring IGMP 384
- Configuring IGMP 385
- 9.4.2.5 clear igmpsnooping 389
- 10.2.1.1 show logging server 393
- 10.2.1.2 set logging server 394
- Configuring System Logging 395
- 10.2.1.3 clear logging server 396
- 10.2.1.4 show logging default 397
- 10.2.1.5 set logging default 398
- 10.2.1.7 show logging local 400
- 10.2.1.8 set logging local 401
- 10.2.1.9 clear logging local 402
- 10.2.1.10 show logging buffer 403
- 10.2.2.1 history 405
- 10.2.2.2 show history 406
- 10.2.2.3 set history 407
- 10.2.2.4 ping 408
- 10.2.2.5 show users 410
- 10.2.2.6 disconnect 411
- 10.2.3.1 show arp 413
- 10.2.3.2 clear arp 414
- 10.2.3.3 show mac 415
- • learned 416
- 10.2.3.4 show mac agetime 417
- 10.2.4.1 show sntp 419
- 10.2.4.2 set sntp client 421
- 10.2.4.3 clear sntp client 422
- 10.2.4.4 set sntp server 423
- 10.2.4.5 clear sntp server 424
- 10.2.4.10 set sntp poll-retry 429
- 10.2.5.2 set nodealias 435
- Configuring Node Aliases 436
- Security Configuration 437
- 11.3.1 Configuring RADIUS 439
- 11.3.1.1 show radius 440
- 11.3.1.2 set radius 442
- Configuring RADIUS 443
- 11.3.1.3 clear radius 444
- • IP address 446
- 11.3.2.1 show dot1x 450
- 11.3.2.3 set dot1x 455
- 11.3.2.6 show eapol 460
- 11.3.2.7 set eapol 463
- 11.3.2.8 clear eapol 464
- VLAN id for ingress 470
- 11.3.4.1 show maclock 472
- 11.3.4.3 set maclock enable 476
- 11.3.4.4 set maclock disable 477
- Configuring MAC Locking 478
- 11.3.4.7 set maclock trap 480
- 11.3.5.1 show ssh status 482
- 11.3.5.2 set ssh 483
- 11.3.5.3 set ssh hostkey 484
Prodotti e manuali riguardandi Switch di rete Enterasys Enterasys SecureStack B2 B2G124-24
(12 pagine)
Switch di rete Enterasys 24-Port Manuale Utente
(48 pagine)
(48 pagine)
Switch di rete Enterasys 5H1XX Specifiche
(88 pagine)
(88 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale